4/2/2023 0 Comments Osculator with microsoftSet Transition Position /atem/transition/position.T-bar Reset to Transition Start Position /atem/transition/bar/reset.Preview Transition /atem/transition/preview.Fade to Black Toggle /atem/transition/ftb.To send commands on other mix effect blocks, use the address: /atem/me/$i/transition/., where $i is 1, 2, 3, or 4 Transition Controlīy default, commands will be sent to the first mix effect block (M/E). After the initial fetch, you will also recieve updates when the short or long name is changed in ATEM Software Control. Note: You can fetch the names of each input by sending the /atem/send-status command (detailed later), this will return the short names of each input to /atem/input/$i/short-name and the long names to /atem/input/$i/long-name. Note: The actual numbers vary greatly from device to device, be sure to check the in-app address menu To send commands on other mix effect blocks, use the address: /atem/me/$i/program, where $i is 1, 2, 3, or 4įor preview selection /atem/preview $i can be used.Īlso supports sending the input in the address instead of as a value (e.g. If you add a nickname to a switcher, you must send the nickname in the address, and all feedback messages will contain the nickname in the address.įor example, /atem/my-switcher-1/transition/auto will trigger an automatic transition on the switcher whose nickname is my-switcher-1 Program and Preview Selectionīy default, commands will be sent to the first mix effect block (M/E). If you connect multiple switchers to atemOSC, you will need to provide a nickname for each switcher and use that nickname in the address to specify which switcher to send the command to. By default, all commands without a nickname will be sent to the first switcher with no nickname. If you only want to connect to a single ATEM switcher, leave the nickname field blank and use the addresses below as normal. atemOSC will ignore all OSC commands it receives whose address does not start with /atem/. The list below is just an overview of what the addresses may look like for a generic switcher.Īll addresses must start with /atem/. The full list of the OSC-addresses available for your switcher can be obtained by going to the “OSC Addresses” tab once you’ve connected atemOSC to your switcher. Usage with ProPresenter and OSCulator (MIDI) by Tiffany Howard: Usage with OSCulator (MIDI) by Morgan Warf: Usage with OSCulator (MIDI) by John Barker: Usage with Ableton Live and OSCulator (MIDI) by Jake Gosselin: TouchOSC Layout (iPad) by Peter Steffey:.Open Stage Control Layout by Peter Steffey:.If you would like to control your switcher using a mobile device, you can use TouchOSC or Open Stage Control. If you would like to control AtemOSC directly using MIDI, comment on Issue #111 to let us know. If you would like to control your switcher using a MIDI board or device, consider pairing this software with OSCulator or MidiPipe. SendOSC also enables using AtemOSC with ControllerMate and X-keys. See the actionscript example in this repository for an example of using AppleScript and sendOSC. If you would like to send OSC from AppleScript or Terminal commands, you can download and use the sendosc command. You can find the IP address of a macOS computer by going to System Preferences > Network or by running ifconfig in a terminal window. If you are sending atemOSC messages from another device, you will need to send it to the IP address of the computer running atemOSC on the port that atemOSC is listening on. If you are sending atemOSC messages from a queueing software or translation software on the same computer that atemOSC is running on, make sure to send messages to 127.0.0.1 (localhost) on the port that atemOSC is listening on. If you set an outgoing IP address and port, atemOSC will send status updates and feedback OSC messages to the IP address and port you specified.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |